ISO Fits & Tolerances Calculator
Hole and shaft limits, deviations and the clearance or interference of any ISO 286 fit, such as H7/g6, H7/k6 or H7/p6, for sizes up to 3150 mm. Type a callout straight off the drawing. Free, metric, no login.
For example 25 H7/g6, Ø40 h6 or 12 P7.
Limits from the ISO 286-1 and ISO 286-2 tables of standard tolerances and fundamental deviations. Check critical work against the standard and the drawing.
Drawing gives Ø25 +0.021 / 0 with no class? Enter the size and both deviations to see which ISO class it is.
Capital letter for a hole (H7), small for a shaft (h6).
Preferred fits at Ø25
The ten ISO preferred fits, loosest to tightest, worked out for the size you entered. Click a fit to open it in the calculator.
How it's worked out
A fit callout such as 25 H7/g6 gives the nominal size, the hole class (capital letter) and the shaft class (small letter). The letter places the tolerance zone; the number sets its width.
- IT grade
- The number (01, 0, 1 to 18) is the standard tolerance grade. Its width in µm comes from the ISO 286-1 table for the size range the nominal size falls in, for example IT7 = 21 µm over 18 up to 30 mm.
- Letter
- The fundamental deviation: the limit nearest the zero line. H and h sit on it, a to g (A to G) give clearance, j to n are transition, p to zc (P to ZC) give interference.
- es, ei / ES, EI
- Upper and lower deviation of the shaft / hole. The other limit is the fundamental deviation plus or minus the IT value.
- Δ
- Holes K, M and N up to IT8 and P to ZC up to IT7 get the Δ correction from the standard, so that H7/p6 and P7/h6 give the same fit.
- js, JS
- Symmetric about the zero line, ±IT/2.
- Max clearance
- Largest hole minus smallest shaft (ES − ei).
- Min clearance
- Smallest hole minus largest shaft (EI − es). A negative clearance is interference.
- Fit type
- Clearance if the minimum clearance is zero or more, interference if the maximum clearance is zero or less, transition when it can be either.
- GO / NO-GO
- Plug or ring gauge sizes: GO is the maximum material size (smallest hole, largest shaft), NO-GO the least material size.
- Size range
- Over 0 up to 3150 mm. a, b, c, cd, ef, fg, j, v to zc and their capitals are only tabulated up to 500 mm or less, as in the standard.
Common questions
What does H7/g6 mean on a drawing?
It is a fit between a hole and a shaft. H7 is the hole class: H puts the lower limit on the nominal size and IT grade 7 sets the tolerance width. g6 is the shaft class: g puts the shaft just under the nominal size, IT6 sets its width. For Ø25 H7/g6 the hole is 25.000 to 25.021 mm and the shaft 24.980 to 24.993 mm, a clearance of 0.007 to 0.041 mm.
What is the difference between a clearance, transition and interference fit?
In a clearance fit the smallest hole is always bigger than the largest shaft (letters a to h on the shaft). In an interference fit the largest hole is always smaller than the smallest shaft (p to zc), so the parts are pressed or shrunk together. A transition fit (j to n) can come out either way, depending on where each part lands in its tolerance.
What is an IT grade?
The number in a class such as H7 is the ISO 286 standard tolerance grade, from IT01 (finest) to IT18. Its width depends on the size range: IT7 is 21 µm over 18 up to 30 mm, IT6 is 13 µm in the same range.
Which ISO fit is used for what?
The common hole-basis fits are H11/c11 loose running, H9/d9 free running, H8/f7 close running, H7/g6 sliding, H7/h6 locational clearance, H7/k6 and H7/n6 locational transition, H7/p6 locational interference, H7/s6 medium drive and H7/u6 force fit. For bearings, use the bearing maker's recommended shaft and housing tolerances.
What size should I machine to?
The calculator gives the mid-limit size, halfway between the upper and lower limit, which leaves the most room either way. GO and NO-GO gauge sizes are the maximum and least material sizes.